manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

85.  Virtual Router Redundancy Protocol (VRRP) Command List        

965

Parameters

Restrictions

None.

Example

To display the VRRP configuration:

85.8. config vrrp trap state

Description

This command is used to configure the trap sending state of the VRRP.

ipif

(Optional) Specifies the IP interface name to be displayed.
<ipif_name 12>

Enter the IP interface name to be displayed here. This name can be up to 12               
characters long.

vrid

(Optional) Specifies the Virtual Router ID to be displayed.
<vrid 1-255>

Enter the Virtual Router ID to be displayed here. This value must be between 1 and               
255.

If no parameter is specified, then all the VRRP entries will be displayed.

Zxxx0:admin# show vrrp
Command: show vrrp

 Global VRRP            : Disabled
 Non-owner response Ping: Disabled

 Interface Name                : System
 Authentication type           : No Authentication

         VRID                   : 1
         Virtual IP Address     : 10.90.90.91
         Virtual MAC Address    : 00-00-5E-00-01-01
         Virtual Router State   : Initialize
         State                  : Enabled
         Priority               : 100
         Master IP Address      : 10.90.90.90
         Critical IP Address    : 0.0.0.0
         Checking Critical IP   : Disabled
         Advertisement Interval : 1 secs
         Preempt Mode           : True
         Virtual Router Up Time : 0 centi-secs
 Total Entries: 1

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Lindy 32351 Manual preview
32351
Brand: Lindy Pages: 70
Belkin OmniView Secure F1DN102Uea Quick Installation Manual preview
OmniView Secure F1DN102Uea
Brand: Belkin Pages: 36
Maiwe MIEN2208-F User Manual preview
MIEN2208-F
Brand: Maiwe Pages: 5
TP-Link LiteWave LS105G Installation Manual preview
LiteWave LS105G
Brand: TP-Link Pages: 3
Banner PICO-GUARD SFI-D1EDPXT6 Instruction Manual preview
PICO-GUARD SFI-D1EDPXT6
Brand: Banner Pages: 2
3Com 3C16895 Installation Manual preview
3C16895
Brand: 3Com Pages: 74
GarrettCom Ethernet Networks and Web Management Brochure preview
Ethernet Networks and Web Management
Brand: GarrettCom Pages: 12
Net Optics IBPO-HB50SR-XFP User Manual preview
IBPO-HB50SR-XFP
Brand: Net Optics Pages: 53
STI SS2 2 Series Manual preview
SS2 2 Series
Brand: STI Pages: 2
3Com Gigabit Switch 8 Datasheet preview
Gigabit Switch 8
Brand: 3Com Pages: 2
Shadow SH 124 Instructions preview
SH 124
Brand: Shadow Pages: 4
AVPro Edge ConferX AC-CX84-AUHD Quick Start Manual preview
ConferX AC-CX84-AUHD
Brand: AVPro Edge Pages: 6
WaveSplitter WST-PIP001 Operation Manual preview
WST-PIP001
Brand: WaveSplitter Pages: 35
Radio Shack AFX-400 Owner'S Manual preview
AFX-400
Brand: Radio Shack Pages: 16
Cabletron Systems GIGAswitch GSR-16 User'S Reference Manual preview
GIGAswitch GSR-16
Brand: Cabletron Systems Pages: 346
Veris Industries Hawkeye 738 Installation Manual preview
Hawkeye 738
Brand: Veris Industries Pages: 2
ATTE XPOE-4-11-HS User Manual preview
XPOE-4-11-HS
Brand: ATTE Pages: 4
Owon SLC600-D Quick Start Manual preview
SLC600-D
Brand: Owon Pages: 10

Brands by name

Popular brands

Load more brands