manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

55.  Multicast Listener Discovery (MLD) Commands

596

Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

Example

To configure the MLD on the IP interface "System":

max_response_time

(Optional) Specifies the maximum time in seconds to wait for reports from listeners. 
<sec 1-25>

Enter the maximum response time value used here. The value must be between 1             
and 25 seconds. The default value is 10 seconds.

robustness_variable

(Optional) Specifies the permitted packet loss that guarantees the MLD. 
<value 2-7>

Enter the robustness variable value used here. This value must be between 2 and 7.              
The default value is 2.

last_listener_query_interval

(Optional) Specifies the maximum response time inserted into the Multicast address          
specific query sent in response to 'done group' messages. This is also the amount of time               
between Multicast address specific query messages.
<sec 1-25>

Enter the last listener query interval value used here. This value must be between 1              
and 25 seconds. The default value is 1 second.

version (Optional) Specifies the MLD version number.

<value 1-2>

Enter the MLD version number used here. This number must be between 1 and 2.              
The default value is 2.

state

(Optional) Specifies the MLD state for the specified route interface.
enable

Specifies that the MLD state for the specified interface will be enabled.

disable

Specifies that the MLD state for the specified interface will be disabled.

Zxxx0:admin# config mld ipif System version 1 state enabled
Command: config mld ipif System version 1 state enabled

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

D-Link EasySmart DGS-1100-08 Manual preview
EasySmart DGS-1100-08
Brand: D-Link Pages: 44
pathway 7748 Manual preview
7748
Brand: pathway Pages: 28
GE T1000 Technical Manual preview
T1000
Brand: GE Pages: 302
DANLERS CESF PIR Installation Notes preview
CESF PIR
Brand: DANLERS Pages: 2
Clas Ohlson 36-2824 Quick Start Manual preview
36-2824
Brand: Clas Ohlson Pages: 5
Watt Stopper PW-203 Installation Instructions Manual preview
PW-203
Brand: Watt Stopper Pages: 10
Hamlet XHUB330LAN User Manual preview
XHUB330LAN
Brand: Hamlet Pages: 4
S&T kontron KSwitch D3 UM User Manual preview
kontron KSwitch D3 UM
Brand: S&T Pages: 38
Planet WGSW-5240 Specifications preview
WGSW-5240
Brand: Planet Pages: 2
Lindy 32251 and use Installation And Use Manual preview
32251 and use
Brand: Lindy Pages: 54
Opengear IP-KVM 1001 User Manual preview
IP-KVM 1001
Brand: Opengear Pages: 109
Eaton Cutler-Hammer RTHMFDA20100WSU Instructions Manual preview
Cutler-Hammer RTHMFDA20100WSU
Brand: Eaton Pages: 28
WilTec SKD-1 Operation Manual preview
SKD-1
Brand: WilTec Pages: 7
Enterasys VH-8G-L3 User Manual preview
VH-8G-L3
Brand: Enterasys Pages: 41
Cable Electronics CE Labs HSW44C Instruction Manual preview
CE Labs HSW44C
Brand: Cable Electronics Pages: 12
Audiovox Signal Distribution Box SDB45 Owner'S Manual preview
Signal Distribution Box SDB45
Brand: Audiovox Pages: 12
Enterasys SecureStack B2 B2G124-48P Hardware Installation Manual preview
SecureStack B2 B2G124-48P
Brand: Enterasys Pages: 91
MicroNet SP684C User Manual preview
SP684C
Brand: MicroNet Pages: 74

Brands by name

Popular brands

Load more brands