manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

79.  Switch Port Commands

908

Restrictions

Only Administrator and Operator-level users can issue this command.

Example

To  configure  the  speed  of  ports  1  to  3  to  be  10  Mbps,  with  full  duplex,  learning                

enabled, state enabled, and flow control enabled:

state

Enable or disable the state of the specified port. If the ports are in error-disabled status,               
configuring their state to enable will recover these ports from a disabled to an enabled              
state. The default value is enable.
enable

Enable the specified port(s).

disable

Disable the specified port(s).

mdix

Specify the type of cabling. The default value is auto.
auto Select auto for auto sensing of the optimal type of cabling.
normal

Select normal for normal cabling. If set to normal state, the port is in MDI mode               
and can be connected to a PC NIC using a straight-through calbe or a port (in MDI                
mode) on another Switching Hub through a cross-over cable.

cross Select cross for cross cabling. If set to cross state, the port is in MDIX mode, and                

can be connected to a port (in MDI mode) on another Switching Hub through a              
straight cable.

description

(Optional) Describe the port interface. 
<desc 1-32>

Describe the port interface.

clear_description

(Optional) Deletes the present description of the port interface.

Zxxx0:admin#config ports 1-3 speed 10_full state enable learning enable 

flow_control enable
Command: config ports 1-3 speed 10_full state enable learning enable flow_control 

enable

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

CALIENT S320 Hardware User'S Manual preview
S320
Brand: CALIENT Pages: 46
CALIENT S320 Getting Started Manual preview
S320
Brand: CALIENT Pages: 42
Western Telematic IPS-800CE-D16, IPS-1600CE-D16 User Manual preview
IPS-800CE-D16, IPS-1600CE-D16
Brand: Western Telematic Pages: 58
H-Tronic TS 1000 Instruction Manual preview
TS 1000
Brand: H-Tronic Pages: 15
Gefen EXT-HDMI-CAT5-844 User Manual preview
EXT-HDMI-CAT5-844
Brand: Gefen Pages: 28
Belkin OMNICUBE F1DK102P Quick Installation Manual preview
OMNICUBE F1DK102P
Brand: Belkin Pages: 21
Xcellon SH10-10H Manual preview
SH10-10H
Brand: Xcellon Pages: 2
Gefen HDMI-341 User Manual preview
HDMI-341
Brand: Gefen Pages: 12
Zamel stiro RWS-211D/N Manual preview
stiro RWS-211D/N
Brand: Zamel Pages: 11
Foxtel FX04241 Quick Install Manual preview
FX04241
Brand: Foxtel Pages: 9
Cabletron Systems SmartSTACK 10 ELS10-26 Getting Started preview
SmartSTACK 10 ELS10-26
Brand: Cabletron Systems Pages: 18
KanexPro 813982020283 User Manual preview
813982020283
Brand: KanexPro Pages: 43
Honeywell 50054911 Installation Manual preview
50054911
Brand: Honeywell Pages: 30
CYP CPLUS-V3H1H Operation Manual preview
CPLUS-V3H1H
Brand: CYP Pages: 20
Honeywell DPSL200 Installation Instructions preview
DPSL200
Brand: Honeywell Pages: 2
Siemens HUB-4 Installation Instructions Manual preview
HUB-4
Brand: Siemens Pages: 16
Siemens RUGGEDCOM RSG2300F Installation Manual preview
RUGGEDCOM RSG2300F
Brand: Siemens Pages: 54
Radial Engineering Pro48 User Manual preview
Pro48
Brand: Radial Engineering Pages: 2

Brands by name

Popular brands

Load more brands