Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 945

Page: 945 / 1058

84. Utility Commands

946

84.14. config rcp server clear



Description

This command is used to clear Remote Copy Protocol (RCP) global server information.



Format

config rcp server clear [ipaddr | username | both]



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To clear the current username of the RCP global server:

Zxxx0:admin#config rcp server username travel
Command: config rcp server username travel

Success.

Zxxx0:admin#

ipaddr

Clear the IP address of the RCP server.

username

Clear the username of the RCP server.

both

Clear both the IP address and the username of the RCP server.

Zxxx0:admin#config rcp server clear username
Command: config rcp server clear username

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands