Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 161

Page: 161 / 1058

12. Basic IP Commands

162



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To create an IP interface petrovic1:

12.3. delete ipif



Description

This command is used to delete an interface or an IPv6 address.



Format

delete ipif [<ipif_name 12> {ipv6address <ipv6networkaddr>} | all]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To delete interface petrovic1:

Zxxx0:admin#create ipif petrovic1 100.1.1.2/16 VLAN598
Command: create ipif petrovic1 100.1.1.2/16 VLAN598

Success.

Zxxx0:admin#

<ipif_name 12>

The name of the interface.
ipv6address

(Optional) The IPv6 network address to be deleted.
<ipv6networkaddr>

The IPv6 network address to be deleted.

all

All IP interfaces except the System IP interface will be deleted.

Zxxx0:admin#delete ipif petrovic1
Command: delete ipif petrovic1

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands