Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 223

Page: 223 / 1058

20. Debug Software Command List

224



Restrictions

Only Administrator-level users can issue this command.



Example

To set all module debug message outputs to local console:

20.4. debug config error_reboot



Description

This command is used to set if the Switching Hub needs to be rebooted when a fatal error

occurs. When the error occurs, the watchdog timer will be disabled by the system first, and

then all debug information will be saved in NVRAM. If the error_reboot is enabled, the

watchdog shall be enabled after all information is stored into NVRAM.



Format

debug config error_reboot [enable | disable]



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To set the Switching Hub to not need a reboot when a fatal error occurs:

Zxxx0:admin# debug output all console
Command: debug output all console

Success.

Zxxx0:admin#

enable

Need reboot Switching Hub when fatal error happens.(if the project do not define the
default setting, enable for default).

disable

Do not need reboot Switching Hub when fatal error happens, system will hang-up for
debug and enter the debug shell mode for debug.

Zxxx0:admin# debug config error_reboot disable
Command: debug config error_reboot disable

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands