Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 922

Page: 922 / 1058

82. Time and SNTP Commands

923



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure time:

offset

Specify the number of minutes to add or to subtract during summertime. The range of
offsets are 30, 60, 90, and 120. The default value is 60.
30

Specify 30 minutes to add or to subtract during summertime.

Specify 60 minutes to add or to subtract during summertime.

Specify 90 minutes to add or to subtract during summertime.

120

Specify 120 minutes to add or to subtract during summertime.

annual

Set the DST to annual mode.

s_date

Configure the start date number of DST.
<start_date 1-31>

Configure the start date number of DST. The values are 1 to 31.

e_date

Configure the end date number of DST.
<end_date 1-31>

Configure the end date number of DST. The values are 1 to 31.

Zxxx0:admin#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2

e_day wed e_mth 10 e_time 15:30 offset 30
Command: config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2

e_day wed e_mth 10 e_time 15:30 offset 30

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands