Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 903

Page: 903 / 1058

78. Subnet VLAN Commands

904

78.4. config vlan_precedence ports



Description

This command is used to configure vlan classification precedence on each port.

You can specify the order of MAC-based VLAN classification and subnet VLAN

classification.

If a port's VLAN classification is MAC-based precedence, MAC-based VLAN

classification will process at first. If MAC-based VLAN classification fails, the subnet

VLAN classification will be executed.

If a port's VLAN classification is subnet VLAN precedence, the subnet VLAN

classification will process at first. If subnet VLAN classification fails, the MAC-based

VLAN classification will be executed.



Format

config vlan_precedence ports <portlist> [mac_based_vlan | subnet_vlan]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure subnet VLAN classification precedence on port 1:

<portlist>Enter a list of ports used for this configuration here.

mac_based_vlan

Specifies that the MAC-based VLAN classification is precedence than subnet VLAN
classification

subnet_vlan

Specifies that the subnet VLAN classification is precedence than MAC-based VLAN
classification

Zxxx0:admin# config vlan_precedence ports 1 subnet_vlan
Command: config vlan_precedence ports 1 subnet_vlan

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands