manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

91.  System Log Lists

1038

91.19. VRRP

#

Serverity

Log message / Explanation

1

Informational

VR <vr-id> at interface <intf-name> switch to Master

One virtual router state becomes Master.

2

Informational

VR <vr-id> at interface <intf-name> switch to Backup

One virtual router state becomes Backup.

3

Informational

VR <vr-id> at interface <intf-name> switch to Init

One virtual router state becomes Init.

4

Warning

Authentication type mismatch on VR <vr-id> at interface <intf-

name>

Authentication type mismatch of one received VRRP 

advertisement message.

5

Warning

Authentication fail on VR <vr-id> at interface <intf-name>. 

Auth type <auth-type>

Authentication checking fail of one received VRRP 

advertisement message.

6

Warning

Received an ADV msg with incorrect checksum on VR <vr-id> 

at interface <intf-name>

Checksum error of one received VRRP advertisement message.

7

Warning

Received ADV msg virtual router ID mismatch. VR <vr-id> at 

interface <intf-name>

Virtual router ID mismatch of one received VRRP 

advertisement message.

8

Warning

Received ADV msg adv interval mismatch. VR <vr-id> at 

interface <intf-name>

Advertisement interval mismatch of one received VRRP 

advertisement message.

9

Notice

Added a virtual MAC <vrrp-mac-addr> into L2 table

A virtual MAC address is added into switch L2 table.

10

Notice

Deleted a virtual MAC <vrrp-mac-addr> from L2 table

A virtual MAC address is deleted from switch L2 table.

11

Notice

Added a virtual IP <vrrp-ip-addr> MAC <vrrp-mac-addr> into L3 

table

A virtual MAC address is adding into switch L3 table.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Ubisys S1 Reference Manual preview
S1
Brand: Ubisys Pages: 40
N-Tron 900 Installation & User Manual preview
900
Brand: N-Tron Pages: 18
C&H Technologies M221 Specifications preview
M221
Brand: C&H Technologies Pages: 1
D-Box G3 Installation Manual preview
G3
Brand: D-Box Pages: 31
Lucent Technologies LambdaUnite MSS Installation Manual preview
LambdaUnite MSS
Brand: Lucent Technologies Pages: 388
Generac Power Systems GenReady Series 005448-2 Overview preview
GenReady Series 005448-2
Brand: Generac Power Systems Pages: 4
Lantech IPES-3408GSFP User Manual preview
IPES-3408GSFP
Brand: Lantech Pages: 119
Fairchild FSDH321 Manual preview
FSDH321
Brand: Fairchild Pages: 20
Omron WLM - Datasheet preview
WLM -
Brand: Omron Pages: 10
Contec SH-9008AT-POE Reference Manual preview
SH-9008AT-POE
Brand: Contec Pages: 38
Black Box 26592 Specifications preview
26592
Brand: Black Box Pages: 3
T.I.P. TLS 100 E Manual preview
TLS 100 E
Brand: T.I.P. Pages: 42
Justin JH-810 User Manual preview
JH-810
Brand: Justin Pages: 8
QSFPTEK S5300-24P4TS Quick Start Manual preview
S5300-24P4TS
Brand: QSFPTEK Pages: 11
Novus NVS-5116SP User Manual preview
NVS-5116SP
Brand: Novus Pages: 24
Pilz 542 183 Operating Manual preview
542 183
Brand: Pilz Pages: 41
GarrettCom Hubs User Manual preview
Hubs
Brand: GarrettCom Pages: 12
Kramer VS-3232DN User Manual preview
VS-3232DN
Brand: Kramer Pages: 149

Brands by name

Popular brands

Load more brands