Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 298

Page: 298 / 1058

23. DHCP Server Commands

299



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the next server:

23.15. config dhcp ping_packets



Description

This command is used to specify the number of ping packets the DHCP server sends to an

IP address before assigning this address to a requesting client.

By default, the DHCP server pings a pool address twice before assigning the address to a

DHCP client. If the ping is unanswered, the DHCP server assumes (with a high probability)

that the address is not in use and assigns the address to the requesting client. If the ping is

answered, the server will discard the current IP address and try another IP address.



Format

config dhcp ping_packets <number 0-10>



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure ping packets:

<pool_name 12>

Specify the DHCP pool name.

<ipaddr>(Optional) Specify the IP address of the next server.

Zxxx0:admin#config dhcp pool next_server engineering 192.168.0.1
Command: config dhcp pool next_server engineering 192.168.0.1

Success.

Zxxx0:admin#

Specify the number of ping packets. 0 means there is no ping test. The default value is 2.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands