manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

62.  Protocol Independent Multicast (PIM) Commands

704

Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

Example

To configure PIM configurations of IP interface System:

state

(Optional) Specifies to allow the PIM function to be disabled or enabled for the above IP               
interface.  The default is disabled.
enable

Specifies that the PIM function will be enabled.

disable

Specifies that the PIM function will be disabled.

mode

(Optional) Specifies the multicast protocol mode used. - dense mode or sparse mode, or             
sm-dm mode. The default value is dense mode.
dm

Specifies that the multicast protocol mode will be set to dense mode.

sm

Specifies that the multicast protocol mode will be set to sparse mode.

sm-dm

Specifies that the multicast protocol mode will be set to both dense and sparse             
mode.

dr_priority

(Optional) Specifies the priority for DR election.
<uint 0-4294967294>

Enter  the  DR  priority  value  used  here.  This  value  must  be  between  0  and             
4294967294.

register_probe_time

Specifies the register probe time. The default value is 5 sec.
<value 1-127>

Enter the register probe time value here. This value must be between 1 and 127.

register_suppression_time

Specifies the register supression time. The default value is 60 sec.
<value 3-255>

Enter the register suppression time value here. This value must be between 3 and             
255.

Zxxx0:admin# config pim ipif System hello 35 jp_interval 70 state enable
Command: config pim ipif System hello 35 jp_interval 70 state enable

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Qlogic SANbox 5802V Supplementary Manual preview
SANbox 5802V
Brand: Qlogic Pages: 4
D-Link DMS-1250 Series Hardware Installation Manual preview
DMS-1250 Series
Brand: D-Link Pages: 38
ORiNG IPS-3082GC-24V Quick Installation Manual preview
IPS-3082GC-24V
Brand: ORiNG Pages: 2
Dahua PFS3005-5ET-V2 Quick Start Manual preview
PFS3005-5ET-V2
Brand: Dahua Pages: 17
Silent Gliss 0913 Installation, Programming And Operation Instructions preview
0913
Brand: Silent Gliss Pages: 4
Raritan SwitchMan USB-Combo SW2 Brochure preview
SwitchMan USB-Combo SW2
Brand: Raritan Pages: 2
Ruby Tech GS-1148L Technical Specifications preview
GS-1148L
Brand: Ruby Tech Pages: 2
Velleman HQ-Power VMS4 Manual preview
HQ-Power VMS4
Brand: Velleman Pages: 5
Eaton STS 2000A Installation And Operation Manual preview
STS 2000A
Brand: Eaton Pages: 120
DANLERS BMEXPIR Installation Notes preview
BMEXPIR
Brand: DANLERS Pages: 2
ANTAIRA LMP-0602 24-V2 Series Quick Installation Manual preview
LMP-0602 24-V2 Series
Brand: ANTAIRA Pages: 2
Key Digital KD-HDMS10X6 Setup Manual preview
KD-HDMS10X6
Brand: Key Digital Pages: 20
Scion-Tech SC01.7050 User Manual preview
SC01.7050
Brand: Scion-Tech Pages: 9
ATEN Altusen KN9008 User Manual preview
Altusen KN9008
Brand: ATEN Pages: 178
Anybus AWB5011 User Manual preview
AWB5011
Brand: Anybus Pages: 126
Comtrend Corporation GS-7260 Quick Start Manual preview
GS-7260
Brand: Comtrend Corporation Pages: 2
PTN WVG2AL USB User Manual preview
WVG2AL USB
Brand: PTN Pages: 12
Theben SEL 173 DCF Operating Instructions Manual preview
SEL 173 DCF
Brand: Theben Pages: 31

Brands by name

Popular brands

Load more brands