Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 108

Page: 108 / 1058

7. Access Control List (ACL) Commands

109



Example

To configure the range of time to activate a function on the Switching Hub:

7.6.

show time_range



Description

This command is used to display current time range settings.



Format

show time_range



Parameters

None.



Restrictions

None.



Example

To display current time range setting:

Zxxx0:admin#config time_range testdaily hours start_time 12:0:0 end_time 13:0:0

weekdays mon,fri
Command: config time_range testdaily hours start_time 12:0:0 end_time 13:0:0

weekdays mon,fri

Success.

Zxxx0:admin#

Zxxx0:admin#show time_range
Command: show time_range

Time Range Information
-------------------------
Range Name   : testdaily
Weekdays   : Mon,Fri
Start Time   : 12:00:00
End Time   : 13:00:00

Total Entries :1

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands