Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 225

Page: 225 / 1058

20. Debug Software Command List

226



Example

To show the error reboot status:

20.7. debug stp clear counter



Description

This command used to clear the STP counters.



Format

debug stp clear counter {ports [<portlist> | all]}



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To clear all STP counters on the Switching Hub:

Zxxx0:admin#debug show error_reboot state
Command: debug show error_reboot state

Error Reboot: Enabled

Zxxx0:admin#

ports

Specifies the port range.
<portlist>

Enter the list of port used for this configuration here.

all

Clears all port counters.

Zxxx0:admin# debug stp clear counter ports all
Command : debug stp clear counter ports all

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands