Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 720

Page: 720 / 1058

62. Protocol Independent Multicast (PIM) Commands

721

62.20. show pim

register_checksum_include_data_rp_list



Description

This command is used to list all the RPs of the registered checksum, including the data.



Format

show pim register_checksum_include_data_rp_list



Parameters

None.



Restrictions

None.



Example

To list all the RPs of the registered checksum, including the data:

Zxxx0:admin# delete pim register_checksum_include_data rp_address 10.54.71.9
Command: delete pim register_checksum_include_data rp_address 10.54.71.9

Success.

Zxxx0:admin#

Zxxx0:admin# show pim register_checksum_include_data_rp_list
Command: show pim register_checksum_include_data_rp_list

PIM Register Full Table

RP adderss
------------------
24.0.0.0
24.1.2.3

Total Entries: 2

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands