Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 256

Page: 256 / 1058

20. Debug Software Command List

257



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To set debug information to output to console:

20.39. debug dhcpv6_relay packet



Description

Used to enable or disable debug information flag for DHCPv6 relay packet, including

packet receiving and sending.



Format

debug dhcpv6_relay packet {all | receiving | sending} state [enable | disable]



Parameters



Restrictions

Only Administrator-level users can issue this command.

output

Specifies the location of the debug message output.
buffer

Let the debug message output to buffer.

console

Let the debug message output to console.

Zxxx0:admin# debug dhcpv6_relay output console
Command: debug dhcpv6_relay output console

Success.

Zxxx0:admin#

all

(Optional) Set packet receiving and sending debug flags.

receiving(Optional) Set packet receiving debug flag.

sending (Optional) Set packet sending debug flag.

state

Specifies if the designated flags function will be enabled or disabled.
enable

Enable the designated flags.

disable

Disable the designated flags.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands