Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 568

Page: 568 / 1058

52. MLD Proxy Commands

569

52.3. config mld_proxy downstream_if



Description

This command configures the MLD proxy downstream interfaces. The MLD proxy plays the

server role on the downstream interfaces. The downstream interface must be an MLD

Snooping enabled VLAN.



Format

config mld_proxy downstream_if [add | delete] vlan [<vlan_name 32> | vlanid <vidlist>]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the MLD Proxy's downstream interface:

add

Specify to add a downstream interface.

delete

Specify to delete a downstream interface .

vlan

Specify the VLAN by name or ID.
<vlan_name 32>

Specify a name of VLAN which belong to the MLD proxy downstream interface.
The maximum length is 32 characters.

vlanidSpecify a list of VLAN IDs which belong to the MLD proxy downstream interface.

Specify a list of VLAN IDs which belong to the MLD proxy downstream
interface.

Zxxx0:admin#config mld_proxy downstream_if add vlan vlanid 2-7
Command: config mld_proxy downstream_if add vlan vlanid 2-7

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands