manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

84.  Utility Commands   

929

Restrictions

Only Administrator-level users can issue this command.

Example

To download runtime firmware from a TFTP server:

dest_file (Optional) Specify an absolute path name on the device file system. If path name is not               

specified, it overwrites the bootup image on the Switch. 
<pathname>

Specify an absolute path name on the device file system.

boot_up (Optional) Specify as boot up file.

cfg_fromTFTP

Download and install new configuration file on the Switching Hub from a TFTP server.
<ipaddr>

Specify the IP address of the TFTP server.

<ipv6addr>

Specify the IPv6 address of the TFTP server.

<domain_name 255>

Specifies  the  domain  name  of  the  TFTP  server.  This  name  can  be  up  to  255              
characters long.

src_file

Specify the path name and file name of the FTP server. It can be a relative path name or                  
an absolute path name. If path name is not specified, it refers to the TFTP server path.                
The maximum length is 64 characters.
<path_filename 64>

Specify the path name and file name of the FTP server. It can be a relative path                
name or an absolute path name. If path name is not specified, it refers to the TFTP                
server path. The maximum length is 64 characters.

unit

Specifies which unit on the stacking system. If it is not specified, it refers to the master                
unit. 
<unit_id 1-4>Enter the unit ID used here.
all

Specifies that all the units in the stacking system will be used.

increment

If increment is specified, then the existing configuration will not be cleared before            
applying of the new configuration. If it is not specified, then the existing configuration             
will be cleared before applying of the new configuration.

dest_file (Optional) Specify an absolute path name on the device. If path name is not specified, it               

refers to the boot up configuration file.
<pathname>

Specify an absolute path name on the device.

Zxxx0:admin#download firmware_fromTFTP 10.0.0.66 src_file runtime.rom dest_file 

runtime.rom
Command: download firmware_fromTFTP 10.0.0.66 src_file runtime.rom dest_file 

runtime.rom

 Connecting to server................... Done.
 Download firmware...................... Done.  Do not power off!
 Please wait, programming flash......... Done.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Xantech AC1 Installation Instructions preview
AC1
Brand: Xantech Pages: 2
Tripp Lite B310-701-4K Owner'S Manual preview
B310-701-4K
Brand: Tripp Lite Pages: 80
West Mountain Radio PWRguard PLUS Operating Manual preview
PWRguard PLUS
Brand: West Mountain Radio Pages: 10
AdLuminis 324002 Quick Start Manual preview
324002
Brand: AdLuminis Pages: 8
E-LINK LNK-IMC208P-SFP Quick Start Manual preview
LNK-IMC208P-SFP
Brand: E-LINK Pages: 6
Velleman HQ-Power VMS4 Manual preview
HQ-Power VMS4
Brand: Velleman Pages: 5
Eaton STS 2000A Installation And Operation Manual preview
STS 2000A
Brand: Eaton Pages: 120
3Com 3CB9E7 - CoreBuilder 9000 Chassis Switch Getting Started Manual preview
3CB9E7 - CoreBuilder 9000 Chassis Switch
Brand: 3Com Pages: 132
Orei UHD-401MV User Manual preview
UHD-401MV
Brand: Orei Pages: 27
TESmart HDK0402A1U User Manual preview
HDK0402A1U
Brand: TESmart Pages: 12
Advantech EKI-7659CPI User Manual preview
EKI-7659CPI
Brand: Advantech Pages: 101
Black Box KV1044A-R2 Specifications preview
KV1044A-R2
Brand: Black Box Pages: 4
Minicom DX DX 432 Operating Manual preview
DX 432
Brand: Minicom DX Pages: 36
Black Box LB9007A-SC-R Installation preview
LB9007A-SC-R
Brand: Black Box Pages: 2
NewStar NS-211KA User Manual preview
NS-211KA
Brand: NewStar Pages: 10
MiLAN MIL-S8TA User Manual preview
MIL-S8TA
Brand: MiLAN Pages: 13
Allied Telesis AT-GS903SX Installation Manual preview
AT-GS903SX
Brand: Allied Telesis Pages: 44
Grandbeing MX0808-31F Operating Instructions Manual preview
MX0808-31F
Brand: Grandbeing Pages: 27

Brands by name

Popular brands

Load more brands