Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 440

Page: 440 / 1058

38. IP Routing Commands

441

38.5. delete ipv6route



Description

This command is used to delete an IPv6 static route from the Switching Hub's IP

routing table. If the next hop is a global address, it is not necessary to indicate the

interface name. If the next hop is a link local address, then the interface name must

be specified.



Format

delete ipv6route [[default | <ipv6networkaddr>] [<ipif_name 12> <ipv6addr> |

<ipv6addr> | ip_tunnel <tunnel_name 12>] | all]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To delete an IPv6 static route:

default Specify the default route.

Specify the IPv6 network address.

<ipif_name 12> <ipv6addr>

Specify the IP interface name.

Specify the next hop address for the IPv6 route

ip_tunnel

Specifies the IPv6 tunnel name used.
<tunnel_name 12>

Enter the IPv6 tunnel name used here. This name can be up to 12 characters long.

all

All static created routes will be deleted.

Zxxx0:admin#delete ipv6route default System FEC0::5
Command: delete ipv6route default System FEC0::5

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands