Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 972

Page: 972 / 1058

86. Voice VLAN Commands

973

86.7. config voice_vlan aging_time



Description

This command is used to set the aging time of the voice VLAN. The aging time is used to

remove a port from voice VLAN if the port is an automatic VLAN member. When the last

voice device stops sending traffic and the MAC address of this voice device is aged out, the

voice VLAN aging timer will be started. The port will be removed from the voice VLAN after

expiration of voice VLAN aging timer. If the voice traffic resumes during the aging time, the

aging timer will be reset and stop.



Format

config voice_vlan aging_time <min 1-65535>



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To set 60 minutes as the aging time of voice VLAN:

86.8. show voice_vlan



Description

This command is used to display voice VLAN global information.



Format

show voice_vlan

Specify the aging time. The range is 1 to 65535 minutes. The default value is 720
minutes.

Zxxx0:admin#config voice_vlan aging_time 60
Command: config voice_vlan aging_time 60

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands