manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

8.  Access Control List (ACL) Egress Command List

136

exceed

Specify the action when packet is in "yellow color".
permit

(Optional) Permit the packet.

replace_dscp

Changes the DSCP of the packet.
<value 0-63>

Enter the DSCP replace value here. This value must be between 0 and 63.

drop Drops the packet.
counter

(Optional) Specifies the ACL counter. This is optional. The default is "disable". The            
resource may be limited so that a counter cannot be turned on. Counters will be              
cleared when the function is disabled.
enable

Specifies that the ACL counter parameter will be enabled.

disable

Specifies that the ACL counter parameter will be disabled.

violate

Specify the action when packet is in "red color".
permit

Permit the packet.

replace_dscp

(Optional) Changes the DSCP of the packet.
<value 0-63>

Enter the DSCP replace value here. This value must be between 0 and 63.

drop Drops the packet.
counter

(Optional) Specifies the ACL counter. This is optional. The default is "disable". The            
resource may be limited so that a counter cannot be turned on. Counters will be              
cleared when the function is disabled.
enable

Specifies that the ACL counter parameter will be enabled.

disable

Specifies that the ACL counter parameter will be disabled.

sr_tcm

Specify the "single rate three color mode".
cir

Specifies the single rate three color mode used.
<value 0-1048576>

Enter the single rate three color mode value here. This value must be 
between 0 and 1048576.

cbs

Specify the "committed burst size". The unit is Kbytes.
<value 0-131072>

Enter the committed burst size value here. This value must be between 0 and 
131072.

ebs

Specify the "Excess Burst Size". The unit is Kbytes.
<value 0-131072>

Enter the excess burst size value here. This value must be between 0 and 
131072.

color_blind

(Optional) Specify the meter mode to be color-blind. The default is color-blind           
mode.

color_aware

(Optional) Specify the meter mode to be color-aware. When this code is specified,            
user  could  set  the  "in-coming  packet  color"  by  using  command  "config          
color_aware". The final color of packet is determined by the initial color of packet             
and the metering result.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

GE SE-100E Instructions Manual preview
SE-100E
Brand: GE Pages: 20
Hama S2100 Operating Instruction preview
S2100
Brand: Hama Pages: 18
3Com NBX 100 Release Note preview
NBX 100
Brand: 3Com Pages: 8
GarrettCom MAGNUM 6KM Installation And User Manual preview
MAGNUM 6KM
Brand: GarrettCom Pages: 24
Lindy 32351 Manual preview
32351
Brand: Lindy Pages: 70
Linkskey LKU -UA02 Quick Installation Manual preview
LKU -UA02
Brand: Linkskey Pages: 2
SMC Networks SMC8606SX Specification Sheet preview
SMC8606SX
Brand: SMC Networks Pages: 2
Green Brook KingShield T206-C Installation And Operating Instruction preview
KingShield T206-C
Brand: Green Brook Pages: 2
Pulsar SG108 Quick Start Manual preview
SG108
Brand: Pulsar Pages: 5
VigilLink VL-MX88-1 User Manual preview
VL-MX88-1
Brand: VigilLink Pages: 24
Cross Technologies 1582-650 Instruction Manual preview
1582-650
Brand: Cross Technologies Pages: 11
Comnet CNGE2FE8MSPOE2 Installation And Operation Manual preview
CNGE2FE8MSPOE2
Brand: Comnet Pages: 105
IOGear GUD3C8K2P Quick Start Manual preview
GUD3C8K2P
Brand: IOGear Pages: 10
Grizzly G8295 Instruction Sheet preview
G8295
Brand: Grizzly Pages: 2
Targus ACH129 User Manual preview
ACH129
Brand: Targus Pages: 30
Nortek GoControl WA00Z-1 Instruction Manual preview
GoControl WA00Z-1
Brand: Nortek Pages: 4
HBM SOMAT XR EX23-R Quick Start Manual preview
SOMAT XR EX23-R
Brand: HBM Pages: 2
Zamel YNSTA PDJ-213 Quick Manual preview
YNSTA PDJ-213
Brand: Zamel Pages: 12

Brands by name

Popular brands

Load more brands