Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 299

Page: 299 / 1058

23. DHCP Server Commands

300

23.16. config dhcp ping_timeout



Description

This command is used to specify the amount of time the DHCP server must wait before

timing out a ping packet.

By default, the DHCP server waits 100 milliseconds before timing out a ping packet.



Format

config dhcp ping_timeout <millisecond 10-2000>



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the time out value for ping packets:

Zxxx0:admin#config dhcp ping_packets 4
Command: config dhcp ping_packets 4

Success.

Zxxx0:admin#

Specify the amount of time the DHCP server must wait before timing out a ping packet.
The default value is 100.

Zxxx0:admin#config dhcp ping_timeout 500
Command: config dhcp ping_timeout 500

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands