Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 145

Page: 145 / 1058

9. ARP Commands

146



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To disable the ARP refresh state:

9.5.

config arp_aging time



Description

This command is used to set the maximum amount of time, in minutes, that an ARP

entry can remain in the Switching Hub

s ARP table, without being accessed, before it

is dropped from the table.



Format

config arp_aging time <min 0-65535>



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

state

Enable or disable the ARP refresh. The default is enable.
enable

Enable the ARP refresh.

disable

Disable the ARP refresh.

Zxxx0:admin#config arp refresh time_out state disable
Command: config arp refresh time_out state disable

Success.

Zxxx0:admin#

The ARP age-out time, in minutes. The default is 20 minutes. The range is 0 to 65535
minutes.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands