manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

12.  Basic IP Commands    

165

12.7. enable ipif_ipv6_link_local_auto

Description

This  command  is  used  to  enable  the  auto  configuration  of  link  local  address  when             

there  are  no  IPv6  addresses  explicitly  configured.  When  an  IPv6  address  is  explicitly            

configured,  the  link  local  address  will  be  automatically  configured,  and  the  IPv6           

processing  will  be  started.  When  there  is  no  IPv6  address  explicitly  configured,  by            

default, link local address is not configured and the IPv6 processing will be disabled.             

By enabling this automatic configuration, the link local address will be automatically           

configured and IPv6 processing will be started.

Format

enable ipif_ipv6_link_local_auto [<ipif_name 12> | all]

Parameters

Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

Zxxx0:admin#show ipif
Command: show ipif

IP Interface                : System
VLAN Name                   : default
Interface Admin State       : Enabled
IPv4 Address                : 10.90.90.90/8 (Manual)  Primary
Proxy ARP                   : Disabled   (Local : Disabled)
IP Directed Broadcast       : Disabled
IPv4 State                  : Enabled
IPv6 State                  : Enabled
IP MTU                      : 1500

IP Interface                : mgmt_ipif
Status                      : Enabled
IP Address                  : 192.168.0.1
Subnet Mask                 : 255.255.255.0
Gateway                     : 0.0.0.0
Link Status                 : Link Down

Total Entries: 2

Zxxx0:admin#

<ipif_name 12>

The name of the interface. 

all

All of the IP interfaces. 

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

E-T-A 921 Series Instructions For Installation Manual preview
921 Series
Brand: E-T-A Pages: 6
Lantech IGS-2206C User Manual preview
IGS-2206C
Brand: Lantech Pages: 118
Belkin 24-Port Gigabit Switch Specifications preview
24-Port Gigabit Switch
Brand: Belkin Pages: 2
CYP OR-HD88HC Operation Manual preview
OR-HD88HC
Brand: CYP Pages: 20
PABX 208AC Instruction Manual preview
208AC
Brand: PABX Pages: 46
Cabletron Systems MicroMMAC-22E Installation Manual preview
MicroMMAC-22E
Brand: Cabletron Systems Pages: 83
KYLAND SICOM3432G Series Hardware Installation Manual preview
SICOM3432G Series
Brand: KYLAND Pages: 29
Penguin Computing Arctica 1600cs Installation Manual preview
Arctica 1600cs
Brand: Penguin Computing Pages: 71
MiLAN MIL-S8TA User Manual preview
MIL-S8TA
Brand: MiLAN Pages: 13
Alps Electric SKRN Series Specifications preview
SKRN Series
Brand: Alps Electric Pages: 4
Linksys SRW2024P User Manual preview
SRW2024P
Brand: Linksys Pages: 110
Gefen HDMI-341 User Manual preview
HDMI-341
Brand: Gefen Pages: 12
Linksys LGS310C Quick Start Manual preview
LGS310C
Brand: Linksys Pages: 4
Lindy 42346 User Manual preview
42346
Brand: Lindy Pages: 16
Rosewill RHB320 User Manual preview
RHB320
Brand: Rosewill Pages: 3
Linksys SRW224P - 10/100 - Gigabit Switch User Manual preview
SRW224P - 10/100 - Gigabit Switch
Brand: Linksys Pages: 69
Oracle Sun Datacenter InfiniBand Switch 648 Installation Manual preview
Sun Datacenter InfiniBand Switch 648
Brand: Oracle Pages: 140
Rose electronics UCR-1R1X16U/2 Installation And Operation Manual preview
UCR-1R1X16U/2
Brand: Rose electronics Pages: 68

Brands by name

Popular brands

Load more brands