Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 721

Page: 721 / 1058

62. Protocol Independent Multicast (PIM) Commands

722

62.21. config pim-ssm



Description

This command is used to enable the SSM (Source-Specific Multicast) service model in PIM-

SM on the Switching Hub. The PIM-SSM function will take active only when SSM service

model and PIM-SM state both enabled.



Format

config pim-ssm {state [enable | disable] | group_range [default | <network_address>]}



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure PIM-SSM state and group range:

state

(Optional) Specifies to enable or disable the SSM service model on the Switch
enable

Specifies that the SSM service model will be enabled.

disable

Specifies that the SSM service model will be disabled.

group_range

(Optional) Specifies the group address range for the SSM service in IPv4.
default

The default indicates that the group address range is 232.0.0.0/8.

<network_address>

Enter the group address range for the SSM service here.

Zxxx0:admin# config pim-ssm state enable group_range default
Command: config pim-ssm state enable group_range default

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands