Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 871 | Manualshive

Page: 871 / 1058

background image

74. Spanning Tree Protocol (STP) commands

872



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure STP:

maxage Specify to determine if a BPDU is valid.

<value 6-40>

Specify to determine if a BPDU is valid. The default value is 20.

maxhopsSpecify to restrict the forwarded times of one BPDU.

<value 6-40>

Specify to restrict the forwarded times of one BPDU. The default value is 20.

hellotimeSpecify the time interval for sending Configuration BPDUs by the Root Bridge. This

parameter is for STP and RSTP version. MSTP version uses per-port hellotime parameter.
<value 1-2>

Specify the time interval for sending Configuration BPDUs by the Root Bridge. This
parameter is for STP and RSTP version. MSTP version uses per-port hellotime
parameter. The default value is 2 seconds.

forwarddelay

Specify the maximum delay time for one BPDU to be transmitted by a bridge and
received from another bridge.
<value 4-30>

Specify the maximum delay time for one BPDU to be transmitted by a bridge and
received from another bridge. The default value is 15.

txholdcount

Specify to restrict the numbers of BPDU transmitted in a time interval (per Hello Time).
<value 1-10>

Specify to restrict the numbers of BPDU transmitted in a time interval (per Hello
Time).

fbpdu

To decide if the Bridge will flood STP BPDU when STP functionality is disabled.
enable

Specify to enable FBPDU.

disable

Specify to disable FBPDU.

nni_bpdu_addr

Specify to determine the BPDU protocol address for STP in service provide site. It can use
802.1d STP address, 802.1ad service provider STP address.
dot1d

Specify to use an 802.1d STP address.

dot1ad

Specify to use an 802.1ad service provider STP address.

Zxxx0:admin# config stp maxage 25
Command: config stp maxage 25

Success.

Zxxx0:admin#

«
...
869
870
871
872
873
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: Gefen Pages: 11

xStack DES-3500 Series

Brand: D-Link Pages: 260

DXS-3600 Series

Brand: D-Link Pages: 48

DXS-3400 SERIES

Brand: D-Link Pages: 3

Web Smart Switch DGS-1210-16

Brand: D-Link Pages: 71

Brand: D-Link Pages: 3

Brand: D-Link Pages: 56

xStack DES-3800 Series

Brand: D-Link Pages: 326

xStack DES-3526

Brand: D-Link Pages: 222

Brand: D-Link Pages: 2

DXS-1210 Series

Brand: D-Link Pages: 20

Brand: Fantech Pages: 4

Brand: Xantech Pages: 2

Brand: Vector Pages: 6

Brand: CalDigit Pages: 13

Brand: hager Pages: 2

Brand: PureLink Pages: 10

Brand: N-Tron Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands