Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 24 | Manualshive

Page: 24 / 1058

background image

4. Using Command Line Interface

25

In the above example, the Switch was assigned an IP address of 10.24.22.100 with a

subnet mask of 255.0.0.0. The system message Success indicates that the command was

executed successfully. The Switch can now be configured and managed via Telnet, SNMP

MIB browser and the CLI or via the Web-based management agent using the above IP

address to connect to the Switch.

There are a number of helpful features included in the CLI. Entering the ? command will

display a list of all of the top-level commands.

When entering a command without its required parameters, the CLI will prompt you with a

Next possible completions: message.

In this case, the command config account was entered with the parameter <username>.

The CLI will then prompt to enter the <username> with the message, Next possible

completions:. Every command in the CLI has this feature, and complex commands have

several layers of parameter prompting.

In addition, after typing any given command plus one space, users can see all of the next

possible sub-commands, in sequential order, by repeatedly pressing the Tab key.

To re-enter the previous command at the command prompt, press the up arrow cursor key.

The previous command will appear at the command prompt.

Zxxx0:admin#?
Command: ?

..
?
cable_diag ports
cd
change drive
clear
clear address_binding dhcp_snoop binding_entry ports
clear address_binding nd_snoop binding_entry ports
clear arptable
clear attack_log
clear counters
clear dhcp binding
clear dhcp conflict_ip
clear dhcpv6 binding

CTRL+C ESC q

Quit

SPACE

n

Next Page

ENTER

Next Entry

a

All

Zxxx0:admin#config account
Command: config account
Next possible completions:
<username>

Zxxx0:admin#

Zxxx0:admin# config account
Command: config account
Next possible completions:
<username>

Zxxx0:admin# config account

«
...
22
23
24
25
26
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: KELCO Pages: 22

Brand: Aastra Pages: 12

Brand: Aastra Pages: 2

Brand: JB Systems Light Pages: 15

Brand: NBase Communications Pages: 72

Brand: Magnum Pages: 3

Cyber SWITCH 1000

Brand: Cabletron Systems Pages: 106

Brand: PNI Pages: 92

Brand: Omron Pages: 10

Brand: Jerguson Pages: 16

Brand: 3Com Pages: 62

Brand: Black Box Pages: 13

Gigabit Switch 8

Brand: 3Com Pages: 2

Brand: Shadow Pages: 4

Extricom AT-EXLS-3000

Brand: Allied Telesis Pages: 120

Brand: D+H Pages: 16

Brand: Kramer Pages: 12

Brand: Quintum Pages: 125

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands