Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 13

Page: 13 / 1058

1. Product Outline

1.4.

Part Names and Functions

ヴヵモヤレチリュチロユュ

Fig. 1-1 Back, Front, LEDs

● Power port

Connect the supplied power cord into the port and connect the other end into an elec

tric outlet.

● Power cord hook block

Hooking the supplied power cord on the block makes the cord less likely to be

unplugged from the power port.

● Ground terminal

Connect the earth terminal screw and grounding surface using the earth wire.

● SD card slot

Insert a SD card to change configuration information and change and save firmware.

● 10BASE-T/100BASE-TX/1000BASE-T port (Ports 1 to 24)

Connect a 10BASE-T/100BASE-TX/1000BASE-T terminal hub repeater Switching Hub.

The length of the copper cabling (CAT5e or higher) connecting this Switching Hub and a

device must be 100 m or shorter.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands