manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

71.  Routing Information Protocol (RIP) Command List

826

Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

Example

To change the RIP receive mode for the IP interface System:

tx_mode(Optional) Specifies the RIP transmission mode.

disable

Specifies to prevent the transmission of RIP packets.

v1_only

Specifies that only RIP version 1 format packets will be transmitted.

v1_compatible

Specifies to transmit RIP version 2 format packets to the broadcast address.

v2_only

Specifies that only RIP version 2 format packets will be transmitted.

rx_mode(Optional) Specifies the RIP receive mode.

v1_only

Specifies to receive RIP version 1 format packets to the RIP multicast address.

v2_only

Specifies to receive RIP version 2 format packets to the RIP multicast address.

v1_or_v2

Specifies to receive both v1 and v2 packet.

disable

Specifies that the receiving of RIP packets will be prevented.

state

(Optional) Specifies that the RIP state will be enabled or disabled. If the state is disabled,               
then RIP packets will not be either transmitted or received by the interface. The network              
configured on this interface will not be in the RIP database.
enable

Specifeies that the RIP state will be enabled

disable

Specifeies that the RIP state will be disabled.

Zxxx0:admin# config rip ipif System rx_mode v1_only
Command: config rip ipif System rx_mode v1_only

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

BERNSTEIN KFM Operating Instructions preview
KFM
Brand: BERNSTEIN Pages: 3
StarTech.com SV431DHD4KU User Manual preview
SV431DHD4KU
Brand: StarTech.com Pages: 24
AVLT-Power AcePro-CE89-1 Quick Installation Manual preview
AcePro-CE89-1
Brand: AVLT-Power Pages: 12
Greengate VNLW-P-1001-MV-N-V Installation Instructions preview
VNLW-P-1001-MV-N-V
Brand: Greengate Pages: 2
Key Digital HD Flash 4 KD-SW4x1 Operating Instructions Manual preview
HD Flash 4 KD-SW4x1
Brand: Key Digital Pages: 12
Waeco PerfectView GPS300 Installation And Operating Manual preview
PerfectView GPS300
Brand: Waeco Pages: 72
KYLAND SICOM3432G Series Hardware Installation Manual preview
SICOM3432G Series
Brand: KYLAND Pages: 29
W Box Technologies 0E-8P65W4POE Manual preview
0E-8P65W4POE
Brand: W Box Technologies Pages: 10
Kramer VS-211X Quick Start Manual preview
VS-211X
Brand: Kramer Pages: 2
Eagle E301DA Product Manual preview
E301DA
Brand: Eagle Pages: 2
MLis MLB-E4203-28-F User Manual preview
MLB-E4203-28-F
Brand: MLis Pages: 85
Raritan SwitchMan USB-Combo SW4 Quick Installation And Setup Manual preview
SwitchMan USB-Combo SW4
Brand: Raritan Pages: 2
Hailink MX44NN00RK User Manual preview
MX44NN00RK
Brand: Hailink Pages: 6
Vertiv XTE PTS Series Description And Installation Manual preview
XTE PTS Series
Brand: Vertiv Pages: 24
Hammond Leslie CU-1 Owner'S Manual preview
Leslie CU-1
Brand: Hammond Pages: 2
AVProEdge AC-MX44/88-AUHD-HDBT User Manual preview
AC-MX44/88-AUHD-HDBT
Brand: AVProEdge Pages: 32
Emcotec iRC Electronic DPSI TWIN Mini Quick Reference Manual preview
iRC Electronic DPSI TWIN Mini
Brand: Emcotec Pages: 2
Kramer Sierra Video 3264V5Sxl Specifications preview
Sierra Video 3264V5Sxl
Brand: Kramer Pages: 1

Brands by name

Popular brands

Load more brands