Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 423

Page: 423 / 1058

36. IGMP Snooping Commands

424

36.11. create igmp_snooping static_group



Description

This command allows users to create an IGMP snooping static group. Member ports

can be added to the static group. The static member and the dynamic member port

form the member ports of a group. The static group will only take effect when IGMP

snooping is enabled on the VLAN. For those static member ports, the device needs to

emulate the IGMP protocol operation to the querier, and forward the traffic destined

to the multicast group to the member ports.

For a layer 3 device, the device is also responsible to route the packet destined for this

specific group to static member ports. The static member port will only affect V2

IGMP operation. The Reserved IP multicast address 224.0.0.X must be excluded from

the configured group.The VLAN must be created first before a static group can be

created.



Format

create igmp_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To create an IGMP snooping static group on default VLAN, group 239.1.1.1:

vlan

Specify the name of the VLAN on which the router port resides.
<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

vlanid

Specify the VLAN ID list.
<vlanid_list>

Specify the VLAN ID list.

<ipaddr>Specify the multicast group IP address (for Layer 3 Switching Hub).

Zxxx0:admin#create igmp_snooping static_group vlan default 239.1.1.1
Command: create igmp_snooping static_group vlan default 239.1.1.1

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands