Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 92

Page: 92 / 1058

7. Access Control List (ACL) Commands

Specify an IP access control list rule.
vlan Specify a VLAN mask. Only the last 12 bits of the mask will be considered.

<hex 0x0-0x0fff> - (Optional) Specify a VLAN mask.

source_ip_mask

Specify an IP source submask.
<netmask>

Specify an IP source submask.

destination_ip_mask

Specify an IP destination submask.
<netmask>

Specify an IP destination submask.

dscp Specify the DSCP mask.
icmp Specify that the rule applies to ICMP traffic.

type (Optional) Specify the ICMP packet type.
code (Optional) Specify the ICMP code.

igmp Specify that the rule applies to IGMP traffic.

type (Optional) Specify the IGMP packet type.
tcp

Specify that the rule applies to TCP traffic.

src_port_mask

(Optional) Specify the TCP source port mask.
<hex 0x0-0xffff>

Specify the TCP source port mask.

dst_port_mask

(Optional) Specify the TCP destination port mask.
<hex 0x0-0xffff>

Specify the TCP destination port mask.

flag_mask

(Optional) Specify the TCP flag field mask.
all

Specify to check all paramenters below.

urg

(Optional) Specify Urgent Pointer field significant.

ack

(Optional) Specify Acknowledgment field significant.

psh

(Optional) Specify Push Function.

rst

(Optional) Specify to reset the connection.

syn

(Optional) Specify to synchronize sequence numbers.

fin

(Optional) No more data from sender.

udp

Specify that the rule applies to UDP traffic.
src_port_mask

(Optional) Specify the TCP source port mask.
<hex 0x0-0xffff>

Specify the TCP source port mask.

dst_port_mask

(Optional) Specify the TCP destination port mask.
<hex 0x0-0xffff>

Specify the TCP destination port mask.

protocol_id_mask

Specify that the rule applies to the IP protocol ID traffic.
<hex 0x0-0xff>

Specify that the rule applies to the IP protocol ID traffic.

user_define_mask

(Optional) Specify the L4 part mask.
<hex 0x0-0xffffffff>

Specify the L4 part mask.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands