Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 233

Page: 233 / 1058

20. Debug Software Command List

234



Restrictions

Only Administrator-level users can issue this command.



Example

To enable OSPF neighbor state change debug:

To enable OSPF interface state change debug:

To enable all OSPF LSA debug flags:

To enable all OSPF packet debug flags:

To enable all OSPF retransmission debug flags:

redistribution

The state of OSPF redistribution debug.

state

Specifies to set the OSPF debug global state.
enable

Specifies that the OSPF debug global state will be enabled.

disable

Specifies that the OSPF debug global state will be disabled.

Zxxx0:admin# debug ospf neighbor_state_change state enable
Command: debug ospf neighbor_state_change state enable

Success.

Zxxx0:admin#

Zxxx0:admin# debug ospf interface_state_change state enable
Command: debug ospf interface_state_change state enable

Success.

Zxxx0:admin#

Zxxx0:admin# debug ospf lsa all state enable
Command: debug ospf lsa all state enable

Success.

Zxxx0:admin#

Zxxx0:admin# debug ospf packet all state enable
Command: debug ospf packet all state enable

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands