manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

7.  Access Control List (ACL) Commands

102

tcp 

Specify TCP.

src_port

(Optional) Specify the TCP source port range.
<value 0-65535>

Specify the value between 0 and 65535.

mask  (Optional) Specify the mask.

<hex 0x0-0xffff>

Specify the mask.

dst_port

(Optional) Specify the TCP destination port range.
<value 0-65535>

Specify the value between 0 and 65535.

mask  (Optional) Specify the mask.

<hex 0x0-0xffff>

Specify the mask.

udp

Specify UDP.

src_port

(Optional) Specify the UDP source port range.
<value 0-65535>

Specify the value between 0 and 65535.

mask  (Optional) Specify the mask.

<hex 0x0-0xffff>

Specify the mask.

dst_port

(Optional) Specify the UDP destination port range.
<value 0-65535>

Specify the value between 0 and 65535.

mask  Specify the mask.

<hex 0x0-0xffff>

Specify the mask.

icmp Specifies that the rule applies to the value of ICMP traffic.

type Specifies that the rule applies to the value of ICMP type traffic.

<value 0-255>

Enter the ICMP type value used here. This value must be between 0 
and 255.

code  Specifies that the rule applies to the value of ICMP code traffic.

<value 0-255>

Enter the ICMP code value used here. This value must be between 0 
and 255.

port

The access profile rule may be defined for each port on the Switching Hub. The port list is                 
specified by listing the lowest Switching Hub number and the beginning port number on             
that Switching Hub, separated by a colon.
<portlist>

Specify a list of ports.

all 

Specify that the access rule will apply to all ports.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

GE SE-100E Instructions Manual preview
SE-100E
Brand: GE Pages: 20
Hama S2100 Operating Instruction preview
S2100
Brand: Hama Pages: 18
eao 04 Series Assembly Instructions preview
04 Series
Brand: eao Pages: 2
eao 04 Series Assembly Instruction preview
04 Series
Brand: eao Pages: 2
H3C s5820x series Quick Start Manual preview
s5820x series
Brand: H3C Pages: 32
H3C S5830V2 series Mce Command Reference preview
S5830V2 series
Brand: H3C Pages: 22
H3C s5820x series Command Reference Manual preview
s5820x series
Brand: H3C Pages: 488
H3C S10500X Series Installation, Quick Start preview
S10500X Series
Brand: H3C Pages: 3
H3C S7500 Series Manual preview
S7500 Series
Brand: H3C Pages: 8
H3C S7500 Series Command Manual preview
S7500 Series
Brand: H3C Pages: 25
H3C S12500 Series Manual preview
S12500 Series
Brand: H3C Pages: 31
H3C S12500 Series Interface Configuration Manual preview
S12500 Series
Brand: H3C Pages: 23
H3C S12500 Series Software Upgrade preview
S12500 Series
Brand: H3C Pages: 24
H3C S12500 Series Installation Instructions Manual preview
S12500 Series
Brand: H3C Pages: 126
H3C S12500-X Configuration Manual preview
S12500-X
Brand: H3C Pages: 42
H3C S6300 Series Troubleshooting Manual preview
S6300 Series
Brand: H3C Pages: 32
H3C S7500 Series Installation Manual preview
S7500 Series
Brand: H3C Pages: 13
H3C S12500 Series Reference preview
S12500 Series
Brand: H3C Pages: 16

Brands by name

Popular brands

Load more brands