Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 647 | Manualshive

Page: 647 / 1058

background image

59. Open Shortest Path First (OSPF) Command List

648



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

hello_interval

(Optional) Allows the specification of the interval between the transmission of OSPF Hello
packets, in seconds. Between 1 and 65535 seconds can be specified. The Hello Interval,
Dead Interval, Authorization Type, and Authorization Key should be the same for all
routers on the same network.
<sec 1-65535>

Enter the hello packet interval value here. This value must be between 1 and 65535
seconds.

dead_interval

(Optional) Allows the specification of the length of time between the receipt of Hello
packets from a neighbor router before the selected area declares that router down. An
interval between 1 and 65535 seconds can be specified. The Dead Interval must be
evenly divisable by the Hello Interval.
<sec 1-65535>

Enter the dead packet interval value here. This value must be between 1 and 65535
seconds.

authentication

(Optional)Specifies that authentication value.
none

Specifies that the authentication value will be set to none.

simple

Specifies that a simple text password must be specified.
<password 8>

Enter the simple text password value here.

metric

(Optional) Specifies the interface metric used.
<value 1-65535>

Enter the metric value here. This value must be between 1 and 65535.

state

(Optional) Specifies the OSPF interface state here.
enable

Specifies that the state will be set to enabled.

disable

Specifies that the state will be set to disabled.

passive

(Optional) Specifies whether the designated entry to be a passive interface or not. When
the interface is specified to be passive, OSPF protocol packets will neither be sent out or
received.
enable

Specifies that the passive interface will be enabled.

disable

Specifies that the passive interface will be disabled.

«
...
645
646
647
648
649
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: LAUMAS Pages: 40

EdgeSwitch 10 XP

Brand: Ubiquiti Pages: 13

Brand: ATEN Pages: 17

Brand: Enttec Pages: 22

Premasreg 716 Series

Brand: S+S Regeltechnik Pages: 32

Brand: Metrix Pages: 12

Brand: Accton Technology Pages: 10

Brand: Lancom Pages: 23

Brand: IPGARD Pages: 2

START-LINE AGC-3500

Brand: Trust Pages: 16

Brand: Icy Box Pages: 10

Brand: hager Pages: 3

Brand: cable matters Pages: 8

Brand: Articona Pages: 2

Power Switch G0021

Brand: G-Force Pages: 2

Brand: A SYSTEMS Pages: 80

EG5-0702-SFP Series

Brand: Leonton Pages: 21

Brand: jbc Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands