Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 427

Page: 427 / 1058

36. IGMP Snooping Commands

428

36.15. show igmp_snooping statistic counter



Description

This command is used to display the IGMP snooping statistics counter for IGMP

protocol packets that are transmitted or received by the Switching Hub since IGMP

snooping was enabled.



Format

show igmp_snooping statistic counter [vlan <vlan_name 32> | vlanid <vlanid_list> |

ports <portlist>]



Parameters



Restrictions

None.



Example

To display the IGMP snooping statistics counter for port 1:

vlan

Specify a VLAN to be displayed.
<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

vlanid

Specify a list of VLANs to be displayed.
<vlanid_list>

Specify the VLAN ID list.

ports

Specify a list of ports to be displayed.
<portlist>

Specify a list of ports.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands