manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

18.  Network Access Authentication Command List

192

Parameters

Restrictions

Only Administrator, Operator and Power-User level users can issue this command. 

Example

The following example sets the authorization mode and authentication VLAN for all ports.

<portlist>Enter the list of ports to be configured here.

all

Specify all ports on the Switch.

auth_mode

(Optional) Specify the authentication mode used.
port_based

If one of the attached hosts passes the authentication, all hosts on the same port 
will be granted to access network. If the user fails to authorize, this port will keep 
trying the next authentication 

host_based

Every user can be authenticated individually. v2.01 and later, can authenticate 
client on specific authentication VLAN(s) only for WAC.
vlanid

(Optional) Specific authentication VLAN(s). This is useful when different        
VLANs on the Switch have different authentication requirements.

<vidlist>

Enter the VLAN ID list here.

state

(Optional) Specify the VID list's authentication state.

enable

Assign the specified VID list as authentication VLAN(s).

disable

Remove the specified VID list from authentication VLAN(s). If "vlanid" is          

not specified, or all VLANs is disabled, means do not care which VLAN            
the client comes from, the client will be authenticated if the client's           
MAC(not  care  the  VLAN)  is  not  authenticated.  After  the  client  is          
authenticated, the client will not be re-authenticated when received        
from other VLANs. All VLANs are disabled by default.

Zxxx0:admin# config authentication ports all auth_mode host_based vlanid 1 state 

enable
Command: config authentication ports all auth_mode host_based vlanid 1 state enable

Success.

Zxxx0:admin# 

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

3Com NBX 100 Release Note preview
NBX 100
Brand: 3Com Pages: 8
AAVARA PB5000 User Manual preview
PB5000
Brand: AAVARA Pages: 23
i3 International S244 Quick Start Manual preview
S244
Brand: i3 International Pages: 2
D-Link xStack DGS-3427 User Manual preview
xStack DGS-3427
Brand: D-Link Pages: 246
Broadcast Tools Sentinel 3 Installation And Operation Manual preview
Sentinel 3
Brand: Broadcast Tools Pages: 28
Teseq NSG 439 User Manual preview
NSG 439
Brand: Teseq Pages: 60
Zektor HDA604 User Manual preview
HDA604
Brand: Zektor Pages: 84
UNICOM SmartGST-2600M Specifications preview
SmartGST-2600M
Brand: UNICOM Pages: 1
UfiSpace S9180-32X Hardware Installation Manual preview
S9180-32X
Brand: UfiSpace Pages: 25
Equip Vision 332702 Manual preview
Vision 332702
Brand: Equip Pages: 10
Ametek SIL IntelliPoint RF S*R*L Series Installation And Operating Instructions Manual preview
SIL IntelliPoint RF S*R*L Series
Brand: Ametek Pages: 93
Nextech XC5906 Instruction Manual preview
XC5906
Brand: Nextech Pages: 4
JetNet 5018G Series Quick Installation Manual preview
5018G Series
Brand: JetNet Pages: 20
System Q ScatterBox POE308 Quick Start Manual preview
ScatterBox POE308
Brand: System Q Pages: 2
NETGEAR ProSAFE FS526Tv2 Hardware Installation Manual preview
ProSAFE FS526Tv2
Brand: NETGEAR Pages: 20
Scion-Tech SC04.MX22 User Manual preview
SC04.MX22
Brand: Scion-Tech Pages: 9
IRT Electronics AMS-4170 Instruction Book preview
AMS-4170
Brand: IRT Electronics Pages: 17
iNels RFSAI-62B Quick Start Manual preview
RFSAI-62B
Brand: iNels Pages: 7

Brands by name

Popular brands

Load more brands