Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 673

Page: 673 / 1058

60. OSPFv3 Commands

674

60.3. show ospfv3



Description

This command is used to display the OSPFv3 configurations or OSPFv3 interfaces

information.



Format

show ospfv3 {[ipif <ipif_name 12> | all]}



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To display OSPFv3 configurations or interfaces information:

ipif

(Optional) Specifies the OSPFv3 IP interface name used.
<ipif_name 12>

Enter the OSPFv3 IP interface name used here. This name can be up to 12
characters long.

all

Specifies that all the OSPFv3 IP interfaces will be used.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands