Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 248

Page: 248 / 1058

20. Debug Software Command List

249

20.28. debug vrrp



Description

This command is used to set VRRP debug flags.



Format

debug vrrp [vr_state_change | packet [all | {receiving | sending}(1)] | mac_addr_update |

interface_change | timers] state [enable | disable]



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To enable the VRRP virtual router state change debug flag:

To enable all VRRP packet debug flags:

vr_state_change

Specifies the state of the VRRP change debug flags.

packet

Specifies to set the VRRP packet flags.
all

Sets VRRP all packet debug flags.

receiving

(Optional) Set the VRRP packet receiving flag.

sending

(Optional) Set the VRRP packet sending flag.

mac_addr_update

Specifies the state of VRRP MAC debug flags.

interface_change

Specifies the state of VRRP interface debug flags.

timers

Specifies the state of VRRP timer's debug flags.

state

Specifies the state of the configured VRRP debug flags.
enable

Specifies that the configure VRRP debug flag will be enabled.

disable

Specifies that the configure VRRP debug flag will be disabled.

Zxxx0:admin# debug vrrp vr_state_change state enable
Command: debug vrrp vr_state_change state enable

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands