Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 475

Page: 475 / 1058

43. Layer 2 Protocol Tunneling (L2PT) Command List

476

43.Layer 2 Protocol Tunneling (L2PT)

Command List

L2PT is a function to enable transferring of L2 protocol frames, such as

STP and GVRP, to different networks.

In this chapter, you will configure L2PT.

Figure 43-1 L2PT overview

43.1. config l2protocol_tunnel ports



Description

This command is used to configure Layer 2 protocol tunneling on ports.

Layer 2 protocol tunneling is used to tunnel Layer 2 protocol packet.

If a Layer 2 protocol is tunnel-enabled on an UNI, once received the PDU on this port,

the multicast destination address of the PDU will be replaced by Layer 2 protocol

tunneling multicast address. The Layer 2 protocol tunneling multicast address for STP

is 01-05-5D-00-00-00, for GVRP is 01-05-5D-00-00-21, for Layer 2 protocols MAC 01-00-

0C-CC-CC-CC is 01-05-5D-00-00-10 and for protocol MAC 01-00-0C-CC-CC-CD is 01-05-

5D-00-00-11.

config l2protocol_tunnel ports [<portlist> | all] type [uni tunneled_protocol [{stp | gvrp |

protocol_mac [01-00-0C-CC-CC-CC | 01-00-0C-CC-CC-CD]}(1) | all] {threshold <value 0-
65535>} | nni | none]

show l2protocol_tunnel {[uni | nni]}
enable l2protocol_tunnel
disable l2protocol_tunnel

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands