Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 406

Page: 406 / 1058

35. IGMP Proxy Commands

407

35.3. config igmp_proxy downstream_if



Description

This command is used to configure the IGMP proxy downstream interfaces. The IGMP

proxy plays the server role on the downstream interfaces. The downstream interface

must be an IGMP-snooping enabled VLAN.



Format

config igmp_proxy downstream_if [add | delete] vlan [<vlan_name 32> | vlanid

<vidlist>]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the IGMP proxy's downstream interface:

add

Specify to add a downstream interface.

delete

Specify to delete a downstream interface .

vlan

Specify the VLAN by name or ID.
<vlan_name 32>

Specify a name of VLAN which will be added to or deleted from the IGMP proxy
downstream interface. The maximum length is 32 characters.

vlanidSpecify a list of VLAN IDs to be added to or deleted from the IGMP proxy

downstream interface.
<vidlist>

Specify a list of VLAN IDs which will be added to or deleted from the IGMP
proxy downstream interface.

Zxxx0:admin#config igmp_proxy downstream_if add vlan vlanid 2-7
Command: config igmp_proxy downstream_if add vlan vlanid 2-7

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands