Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 98

Page: 98 / 1058

7. Access Control List (ACL) Commands

Specify an IP access control list rule.
vlan Specify the VLAN name.

<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

vlanid

Specify the VLAN ID.
<vlanid 1-4094>

Specify the VLAN ID between 1 and 4094.

mask

(Optional) Specify the mask.
<hex 0x0-0x0fff>

Specify the mask.

source_ip

Specify an IP source address.
<ipaddr>

Specify an IP source address.

mask (Optional) Specify the mask.

Specify the mask.

destination_ip

Specify an IP destination address.
<ipaddr>

Specify an IP destination address.

mask (Optional) Specify the mask.

Specify the mask.

dscp Specify the value of DSCP.

Specify the value of DSCP. The DSCP value ranges from 0 to 63.

icmp Specify the ICMP.

type

(Optional) Specify that the rule will apply to the ICMP Type traffic value.
<value 0-255>

Specify the value between 0 and 255.

code (Optional) Specify that the rule will apply to the ICMP Code traffic value.

Specify the value between 0 and 255.

igmp Specify the IGMP.

type (Optional) Specify that the rule will apply to the IGMP Type traffic value.

Specify the value between 0 and 255.

tcp

Specify TCP.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands