Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 234

Page: 234 / 1058

20. Debug Software Command List

235

To enable all OSPF SPF debug flags:

20.14. debug ospf clear counter



Description

This command is used to reset the OSPF statistic counters.



Format

debug ospf clear counter {packet | neighbor | spf}



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To clear all OSPF statistic counters:

Zxxx0:admin# debug ospf retransmission state enable
Command: debug ospf retransmission state enable

Success.

Zxxx0:admin#

Zxxx0:admin# debug ospf spf all state enable
Command: debug ospf spf all state enable

Success.

Zxxx0:admin#

packet

(Optional) Specifies to reset the OSPF packet counter.

neighbor

(Optional) Specifies to reset the OSPF neighbor event counter.

spf

(Optional) Specifies to reset the OSPF SPF event counter.

If the parameter is not specified, all OSPF counters will be cleared.

Zxxx0:admin# debug ospf clear counter
Command: debug ospf clear counter

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands