Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 114 | Manualshive

Page: 114 / 1058

background image

7. Access Control List (ACL) Commands

115



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure a two rate, three color flow meter:

To replace DSCP action changed to perform on conform (green) and unconform

(yellow and red) packets:

violate

This field denotes the red packet flow. Red packet flows may have excess packets
permitted through or dropped. Users may replace the DSCP field of these packets by
checking its radio button and entering a new DSCP value in the allotted field.
permit

Enter this parameter to allow packet flows that are in the red flow.

replace_dscp

Specifies to change the DSCP of the packet.
<value 0-63>

Enter the replacement DSCP of the packet here. This value must be between
0 and 63.

drop Enter this parameter to drop packets that are in the red flow.
counter

(Optional) Use this parameter to enable or disable the packet counter for the
specified ACL entry in the green flow.
enable

Enable the packet counter for the specified ACL entry in the green flow.

disable

Disable the packet counter for the specified ACL entry in the green flow.

deleteUse this parameter to delete the specified flow meter.

Zxxx0:admin#config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 200 pir

2000 pbs 200 conform replace_dscp 21 exceed drop violate permit
Command: config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 200 pir

2000 pbs 200 conform replace_dscp 21 exceed drop violate permit

Success.

Zxxx0:admin#

Zxxx0:admin# config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 200 pir

2000 pbs 200 exceed permit replace_dscp 21 violate permit replace_dscp 21
Command: config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 200 pir

2000 pbs 200 exceed permit replace_dscp 21 violate permit replace_dscp 21

Success.

Zxxx0:admin#

«
...
112
113
114
115
116
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: CALIENT Pages: 22

Brand: Lantronix Pages: 40

Brand: Lantronix Pages: 2

SISTP1040-551-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 2

SISPM1040-3 L Series

Brand: Lantronix Pages: 2

SISPM1040 L3 Series

Brand: Lantronix Pages: 36

SecureLinx Spider

Brand: Lantronix Pages: 18

Brand: Lantronix Pages: 8

Brand: Lantronix Pages: 6

SISPM1040-582-LRT

Brand: Lantronix Pages: 272

Xpress-Pro SW 52000

Brand: Lantronix Pages: 8

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Brand: Jabra Pages: 4

Brand: Danfoss Pages: 6

EdgeLens INT10G8SR56

Brand: Garland Pages: 76

T0-4 SE2 Series

Brand: Eaton Pages: 2

Brand: SELS Pages: 2

ExtremeSwitching SLX 9540

Brand: Extreme Networks Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands