Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 882

Page: 882 / 1058

75. SSH Commands

883



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure an SSH server maximum session of 3:

maxsession

Specify the SSH server maximum session at the same time.
<int 1-8>

Specify the SSH server maximum session at the same time. The maximum session
value must be between 1 and 8. The default value is 8.

contimeout

Specify the SSH server connection timeout.
<sec 120-600>

Specify the SSH server connection timeout. The connection timeout value must be
between 120 and 600 seconds. The default value is 120 seconds.

authfail Specify the user maximum fail attempts.

Specify the user maximum fail attempts. The maximum authentication fail
attempts must be between 2 and 20. The default value is 2.

rekey

(Optional) Specify the time to re-generate the session key.
10min

Specify 10 minutes to re-generate the session key.

30min

Specify 30 minutes to re-generate the session key.

60min

Specify 60 minutes to re-generate the session key.

never Do not re-generate the session key.

port

Specify a TCP port number between 1 and 65535.
<tcp_port_number 1-65535>

Specify a TCP port number between 1 and 65535.

Zxxx0:admin#config ssh server maxsession 3
Command: config ssh server maxsession 3

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands