Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 496 | Manualshive

Page: 496 / 1058

background image

46. LLDP Commands

497

46.LLDP Commands

LLDP (Link Layer Discovery Protocol) is a function to periodically collect

connected device information. If devices, such as an IP phone, printer, and

network camera, support LLDP, you can learn what devices are connected where.

This function also allows you to identify configuration errors based on collected

information and change the protocol settings or Switching Hub operations

according to the information.

Figure 46-1 LLDP overview

enable lldp
disable lldp
config lldp [message_tx_interval <sec 5-32768> | message_tx_hold_multiplier <int 2-10> |

tx_delay <sec 1-8192> | reinit_delay <sec 1-10>]

show lldp
config lldp forward_message [enable | disable]
config lldp notification_interval <sec 5-3600>
config lldp ports [<portlist> | all] [notification [enable | disable] | admin_status [tx_only | rx_only |

tx_and_rx | disable] | mgt_addr [ipv4 <ipaddr> | ipv6 <ipv6addr>] [enable | disable] |
basic_tlvs [{all} | {port_description | system_name | system_description |
system_capabilities}] [enable | disable] | dot1_tlv_pvid [enable | disable] |
dot1_tlv_protocol_vid [vlan [all | <vlan_name 32>] | vlanid <vidlist>] [enable | disable] |
dot1_tlv_vlan_name [vlan [all | <vlan_name 32>] | vlanid <vidlist>] [enable | disable] |
dot1_tlv_protocol_identity [all | {eapol | lacp | gvrp | stp}] [enable | disable] | dot3_tlvs
[{all} | {mac_phy_configuration_status | link_aggregation | maximum_frame_size}] [enable
| disable]]

show lldp ports {<portlist>}
config lldp_med fast_start repeat_count <value 1-10>
config lldp_med log state [enable | disable]
config lldp_med notification topo_change ports [<portlist> | all] state [enable | disable]

«
...
494
495
496
497
498
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: D-Box Pages: 27

4-Port PoweredUSB 2.0 Hub 011006

Brand: CyberData Pages: 4

FLOW BOSS VFB-DSU

Brand: VADA Pages: 17

Brand: FS Pages: 33

Brand: XtendLan Pages: 24

Brand: V7 Pages: 35

CentreCOM GS970M Series

Brand: Allied Telesis Pages: 21

Brand: Eaton Pages: 2

Brand: JetNet Pages: 20

Brand: AV-Box Pages: 11

Brand: Pakedge Device & Software Pages: 14

Brand: Kramer Pages: 2

Brand: Qvis Pages: 7

Brand: Alaxala Pages: 522

ePowerSwitch 8XM Master

Brand: ADDER Pages: 2

Brand: Led Control Pages: 22

Brand: Lantech Pages: 27

Brand: CAI Networks Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands