Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 16

Page: 16 / 1058

1. Product Outline

● SFP extension slot LED (Ports 21 to 24)

LED

Behavior

Description

LINK/ACT.

Green Light

1000Mbps link established in full-duplex.

Green Blink

Transmitting/receiving packets in 1000Mbps
full-duplex.

Off

No device connected.

● SFP+ extension slot LED (Ports 25 to 28)

LED

Behavior

Description

LINK/ACT.

Green Light

10Gbps link established in full-duplex.

Green Blink

Transmitting packets in 10Gbps full-duplex.

Orange Light

1000Mbps link established.

Orange Blink

Transmitting/receiving packets at 1000Mbps.

Off

No device connected.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands