manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

8.  Access Control List (ACL) Egress Command List        

135

rate_exceed

This specifies the action for packets that exceed the committed rate in single rate "two              
color" mode. The action can be specified as one of the following: 
drop_packet

Drop the packet immediately.

remark_dscp

Mark the packet with a specified DSCP. The packet is set to have the higher drop               
precedence.
<value 0-63>

Enter the remark DSCP value here. This value must be between 0 and 63.

tr_tcm

Specify the "two rate three color mode".
cir

Specifies the two rate three color mode used.
<value 0-1048576>

Enter the two rate three color mode value here. This value must be between 
0 and 1048576.

cbs

(Optional) Specifies the "Committed Burst Size". The unit is Kbytes. That is to say, 1              
means 1Kbytes. This parameter is an optional parameter. The default value is           
4*1024. 
<value 0-131072>

Enter the comitted burst size value here. This value must be between 0 and 
131072.

pir

Specifies the "Peak Information Rate". The unit is in Kbps. PIR should always be             
equal to or greater than CIR.
<value 0-1048576>

Enter the peak information rate value here. This value must be between 0 
and 1048576.

pbs

(Optional) Specifies the "Peak Burst Size". The unit is in Kbytes.
<value 0-131072>

Enter the peak burst size value here. This value must be between 0 and 
131072.

color_blind

(Optional) Specify the meter mode to be color-blind. The default is color-blind           
mode.

color_aware

(Optional) Specify the meter mode to be color-aware. When this code is specified,            
user  could  set  the  "in-coming  packet  color"  by  using  command  "config          
color_aware". The final color of packet is determined by the initial color of packet             
and the metering result.

conform (Optional) Specify the action when packet is in "green color".

permit

Permit the packet.

replace_dscp
Changes the DSCP of the packet.

<value 0-63>

Enter the replace DSCP value here. This value must be between 0 and 63.

counter

(Optional) Specifies the ACL counter. This is optional. The default is "disable". The            
resource may be limited so that a counter cannot be turned on. Counters will be              
cleared when the function is disabled.
enable

Specifies that the ACL counter parameter will be enabled.

disable

Specifies that the ACL counter parameter will be disabled.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

N-Tron 900 Installation & User Manual preview
900
Brand: N-Tron Pages: 18
B&K HD6 User Manual preview
HD6
Brand: B&K Pages: 28
B&K HD6 Getting Started Manual preview
HD6
Brand: B&K Pages: 2
hager EMN005 User Instructions preview
EMN005
Brand: hager Pages: 2
hager HIC4 A Series Quick Start preview
HIC4 A Series
Brand: hager Pages: 4
hager EGN100 Manual preview
EGN100
Brand: hager Pages: 2
Aruba 2930F Series Installation, Safety, And Regulatory Information preview
2930F Series
Brand: Aruba Pages: 6
CTS FOS-3124 SERIES User Manual preview
FOS-3124 SERIES
Brand: CTS Pages: 223
Farallon Fast Starlet User Manual preview
Fast Starlet
Brand: Farallon Pages: 22
StarTech.com VS221HD20 Quick Start Manual preview
VS221HD20
Brand: StarTech.com Pages: 2
Jerguson SAS-16 Installation, Operation & Maintenance Instructions preview
SAS-16
Brand: Jerguson Pages: 4
S&T kontron KSwitch D3 UM User Manual preview
kontron KSwitch D3 UM
Brand: S&T Pages: 38
Versa Technology VX-GPH8245 User Manual preview
VX-GPH8245
Brand: Versa Technology Pages: 26
TCi 13811 Installation Manual preview
13811
Brand: TCi Pages: 11
N-audio 8X7 User Manual preview
8X7
Brand: N-audio Pages: 8
Black Box SM508-C-2 Specifications preview
SM508-C-2
Brand: Black Box Pages: 2
Westermo 3635-2210 Manual preview
3635-2210
Brand: Westermo Pages: 22
Asco 911 series Operator'S Manual preview
911 series
Brand: Asco Pages: 20

Brands by name

Popular brands

Load more brands