Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 808

Page: 808 / 1058

69. QoS Commands

809



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the mapping of the DSCP priority to priority 1 on port 1:1 -1:8 :

69.17. config dscp trust



Description

This command is used to configure the state of DSCP trust per port. When DSCP is not

trusted, 802.1p is trusted.



Format

config dscp trust [<portlist> | all] state [enable | disable]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

Enable DSCP trust on ports 1:1-1:8.

Zxxx0:admin#config dscp map 1-8 dscp_priority 1 to 1
Command: config dscp map 1-8 dscp_priority 1 to 1

Success.

Zxxx0:admin#

Enter the list of port used for this configuration here.

all

Specify that the command apply to all ports on the Switch.

state

Enable or disable to trust DSCP. By default, DSCP trust is disabled.
enable

Specify that the DSCP trust state will be enabled.

disable

Specify that the DSCP trust state will be disabled.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands