Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 94

Page: 94 / 1058

7. Access Control List (ACL) Commands



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

ipv6

Specify the IPv6 filtering mask.
class Specify the IPv6 class mask.
flowlabel

Specify the IPv6 flow label mask.

source_ipv6_mask

Specify the IPv6 source IP mask.
<ipv6mask>

Specify the IPv6 source IP mask.

destination_ipv6_mask

Specify the IPv6 destination IP mask.
<ipv6mask>

Specify the IPv6 destination IP mask.

tcp

Specify that the rule applies to TCP traffic.
src_port_mask

(Optional) Specify the TCP source port mask.
<hex 0x0-0xffff>

Specify the TCP source port mask.

dst_port_mask

(Optional) Specify the TCP destination port mask.
<hex 0x0-0xffff>

Specify the TCP destination port mask.

udp - Specify that the rule applies to UDP traffic.

src_port_mask
(Optional) Specify the TCP source port mask.

Specify the TCP source port mask.

dst_port_mask

(Optional) Specify the TCP destination port mask.
<hex 0x0-0xffff>

Specify the TCP destination port mask.

icmp Specify that the rule applies to ICMP traffic.

type (Optional) Specify the ICMP packet type.
code (Optional) Specify the ICMP code.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands