Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 247

Page: 247 / 1058

20. Debug Software Command List

248

20.27. debug ospf state



Description

This command is used to set the OSPF debug global state.



Format

debug ospf state [enable | disable]



Parameters



Restrictions

Only Administrator-level users can issue this command.



Example

To enable the OSPF debug global state:

state

Specifies the OSPF debug global state.
enable

Specifies that the OSPF debug global state will be enabled.

disable

Specifies that the OSPF debug global state will be disabled.

Zxxx0:admin# debug ospf state enable
Command: debug ospf state enable

Success.

Zxxx0:admin# debug ospf show flag
Command: debug ospf show flag

Global State: Enabled

Current OSPF Flags Setting:

Neighbor State Change

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands