Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 446

Page: 446 / 1058

39. IP Source Address Verify Commands

447



Example

To enable IPSG on port1:

39.2. config arp_inspection ports



Description

This command is used to configure the per port state of dynamic ARP inspection on

the Switching Hub. If a port has been configured as group member of an aggregated

link, then the dynamic ARP inspection function cannot be enabled. When the

dynamic ARP inspection is enabled on the port, all ARP packets will be checked under

this mode. In this mode, the legal ARP packets will be forwarded, while the illegal

packets will be dropped.



Format

config arp_inspection ports [<portlist>| all] state [enable | disable]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To enable dynamic ARP inspection on port1:

Zxxx0:admin# config ip_verify_source ports 1 state enable
Command: config ip_verify_source ports 1 state enable

Success.

Zxxx0:admin#

state

enable

Enable the dynamic ARP inspection function. The legal ARP packets will be
forwarded, while the illegal ARP packets will be dropped.

disable

Disable the dynamic ARP inspection function. The default value is disable.

Zxxx0:admin# config arp_inspection ports 1 state enable
Command: config arp_inspection ports 1 state enable

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands